The usefulness of load cells cannot be underestimated. These small devices permeate a whole array of equipment across hundreds of industries. Read on to find out more about this humble yet essential force and weight measurement tool.


A load cell is simply a device that senses an applied physical force and then gives an observable output quantity that is proportional to the applied force. There are different types of load cells , most of which are; strain gauge load cell, hydraulic load cell, pneumatic load cell, capacitive load cell etc. Generally load cells are weight/force measuring devices Each load cell has its mode of operation and characteristics, but the most common is the strain gauge load cell which is basically a transducer. It is a transducer because it produces a measurable electrical signal whose magnitude is proportional to that applied physical force.


equal arm balance

The load cell which is a load (force and weight) measuring device is used for various industrial processes, however before its invention there existed other load weighing instruments dating far back from ancient civilizations such as the ancient Egyptians. During the ancient Egyptian civilization around 3500BC, the Egyptians adopted a tool called "The Equal Arm Balance” . The balance consisted of a column with a horizontal bar at its top that holds two pans at each end, the bar and the pans are attached to each other by a rope. Below is a picture of the balance.

steel yard balance

Then 2500 years after this, a form of unequal arm balance called the “steel yard balance” was invented by the Romans. It consisted of a scaled metal arm suspended off center from above by a hook close to the shorter arm and a known weight called a poise that was attached to the longer arm. This allowed it to gradually slide until it balanced the load attached to the shorter arm. The weight of the unknown load is then obtained based on the position of the poise on the calibrated arm. Below is a picture of a steelyard balance.

Moving forward, Leonardo Da Vinci invented a gradual dial scale in the late 15th century and this marked a great milestone in weight measuring technologies. It was the first automatic balance system that used the position of the calibrated weights on a mechanical lever to balance and determine an unknown weight.

In the 16th century, the Roberval scale was made by the French mathematician called Gilles Personne de Roberval.

In the 17th century, spring scales were invented and they created a non-counter weight approach to weight measurement, which is based on Hooke’s law. The scale consists of a spring attached at one end, a hook at the other end to which the object to be weighed is attached and a pointer that moves along the markings on the body of the scale. The position of the pointer is proportional to the weight attached to the hook, that is, the weight attached stretches the internal spring of the device.

The devices mentioned above were the major weight measuring devices that existed before actual load cells were invented. Pneumatic and hydraulic load cells were the first set of load cell designs to exist before strain gauge load cells.

The English physicist Sir Charles Wheatstone devised the bridge circuit in 1843, it measured electrical resistances. This circuit formed the basis for modern load cell circuitry as the arms of the bridge circuit are fixed with strain gauges. The strain gauge is a bonded wire device that changes its resistance when it is deformed (stretched/contracted). Strain gauge load cells are the most common form of load cells due to their ability to support large load sizes. However Pneumatic and Hydraulic load cells still find their applications in some certain industries.

The advent of strain gauge load cells then resulted in the invention of what is called digital scales, which offer better and more precise load measurement values than earlier weight measurement devices.


Load cells use compressive, bending and tensile force actions to indicate the size of a load. Each type has its basic mode of operation and they are explained below:

Pneumatic load cells

pneumatic drill

Its operation depends on air or gas operated under pressure in a confined space, hence it is a force balance device. The load force to be measured is applied to the top of the diaphragm, the force then creates a pressure that causes the air or gas inside the container to escape through the nozzle and then deflect the pressure gauge.

Hydraulic load cells


This is quite similar to the pneumatic type, but uses a piston-cylinder arrangement that uses a liquid medium under pressure in a confined space, this also makes it a force balance device. The load force to be measured is applied to the piston, this force pushes the piston downwards and deflects the diaphragm, this deflection then increases the pressure in the liquid medium. In other words, the increase in pressure is proportional to the size of the applied force, this change in pressure is then transmitted to the bourdon tube pressure gauge by the liquid medium. It should be noted that the pressure calibration is in Newton, hence the value indicated on the pressure gauge is a measure of the force applied on the piston.

Strain gauge load cells

binocular beam load cell

A strain gauge load cell is a force sensor and also a transducer device. It is a transducer that senses an applied load (force weight) and then changes it into an electrical signal output that is proportional to the load. When a load is placed on the load application point of the load cell, it causes a deformation in the dimensions of the underlying strain gauge, this deformation creates changes in its electrical resistance, hence changes in the output electrical voltage. The voltage is then conditioned to give the proportional value of the load applied.


There are three major types of load cells, namely:

  • Hydraulic load cells
  • Pneumatic load cells
  • Strain gauge load cells

The strain gauge load cell comes in varieties of designs and shapes, but they are majorly of three categories; the full bridge strain gauge load cell (four strain gauge), the half bridge load cell (two strain gauge) and the quarter bridge load cell (one strain gauge).

Other types of load cells are:

  • Vibrating wire load cell
  • Capacitor load cell
  • Piezoelectric load cell


The different load cell types are made from different material parts. Although the different designs of a particular load cell type have common material parts, this section focuses on the material parts of the three common load cells and they are:

Pneumatic load cells: A pneumatic load cell has the following parts; an elastic diaphragm attached with a platform surface to which force can be applied, an air supply regulator, a nozzle and a pressure gauge. Its metal body parts are made of stainless steel. Figure 3 above shows the basic parts of a pneumatic load.

Hydraulic load cells: Its main parts are; an elastic diaphragm, a piston with a loading platform placed on top of the diaphragm, a liquid medium and a bourdon tube pressure gauge. The metal body parts are always made from stainless steel. Figure 5 above shows the basic parts of a hydraulic load cell.

Strain gauge load cells: The major material in this load cell is the strain gauge, they are arranged to form the arms of a Wheatstone bridge circuit. Other components are the spring element, the sealing element and the casing of the device. The casing and other metallic parts of the load cell are usually made from stainless steel. Other basic elements that make up a strain gauge load cell include the spring element, the sealing elements and the housing that helps to protect the load cell components.

It can be seen that they do have some material parts in common especially the metallic parts which is manufactured majorly from Stainless steel. Stainless steel is used by Original Equipment Manufacturers (OEMs) because of its broad range of properties that enable it to withstand great physical stress, thermal stress and bear high loading conditions.


Generally load cells are used for various load bearing and weight/force measuring applications, hence they are LOAD (FORCE and WEIGHT) MEASURING DEVICES.

Their ability to sense force, load and weight makes them applicable in various diverse industries such as the medical and pharmaceutical industry, manufacturing industry, automotive industry, research laboratories, agricultural industry, aerospace and defense industry, robotics systems industry, marine industry, oil and gas industry etc.

They are found in various devices such as weight checkers, weighing scales, medical devices, platform and industrial scales, filling and sorting machineries, rolling mill systems etc.

Load cells are used in devices for various processes such as process weighing, parts counting, medical equipment testing, pile testing, process control and automation monitoring. They're also used in wire tension measurement, silo weight measurement and monitoring, automated container filling, robot tactile sensing and batch weighing. But that's not all, also in automotive seat testing, aerospace structural testing, spring testing, impact force testing, bin weighing, measuring of tie-rod loads, measurement of load of rolling mills in steel works and detection of remaining amount in gas cylinders, etc.

In summary, a load cell is used to measure load (force and weight), its resultant output which is the output of the load cell can then be used for other things such as process control and automation.


steel single ended beam load cell

A strain gauge load cell is one type of load cell, out of the various load cells that exists. It is a force sensor and also a transducer. It is a transducer that senses an applied load (force weight) and then changes it into an electrical signal output that is proportional to the load. The output electrical signal is very small (in mV/V), hence it has to be conditioned to give an output reading.

The conditioning may include amplification, attenuation, excitation, filtering and isolation. For amplification, normal operational amplifiers are not efficient for the process, hence an instrumentation amplifier is always conventionally used in commercial weighing systems.
The strain gauge load cell is made out of strain gauges that are electrically connected in a Wheatstone bridge. The Wheatstone bridge can be of different configurations which are; one strain gauge (Quarter Bridge), two strain gauges (half bridge) and four strain gauges (full bridge). Generally, the number of active elements legs in the Wheatstone bridge determines the kind of bridge configuration.

full bridge strain circuit

The strain gauge is a bonded resistive foil sensor which is capable of stretching and contracting, its resistance varies with applied load. The material deforms/stretches and contract, they are bonded onto a beam or a structural member using adhesives. The strain gauges are mounted in areas that exhibit strain in compression or tension. Most strain gauges are made from a copper-nickel (constantan) alloys, the alloy metal is cut into zigzag foils to form the strain gauge.


strain gauge load cells

Tension load cells are one of the type of strain gauge load cells and are designed to measure tensile loads. A tensile load constitute a tensile pulling force, the tensile force is a load that is applied to a material that acts away from the surface it is applied to. In other words it acts to pull the material or object apart or stretch the material it is acting on (in this case, the material being stretched is the strain gauge).

Tension load cells are of great use for wound or unwound processes e.g. in the production film and ribbons. If the tensile force is too much, the film can break, rendering it useless and creating a lot of down time as the machine will need to be re-threaded. Also if the tensile force is too low when the film is winding, then the rolls are too loose, leaving them prone to exposure or causing other machines to jam. Tension load cells are also used for more than just film, spring coils are also wound with tension load cells to keep the coils from snapping as the metal is bent.

The types of tension load cells include S-beam load cells, columns, and low profile, shackle and link type load cells.


The calibration of load cells is defined as a set of operations carried out to compare the accuracy of the load cell with the standards. Many international standards such as the ISO9000 specify the maximum period between re-calibration as once every two years and more frequently if the instrument deterioration is significant during that period.

However many users perform annual calibration to ensure that measurements are accurate. Some also just compare the current calibration to the previous calibration so as to determine a more suitable re-calibration period.

It should be noted that frequent calibration improves the accuracy and effectiveness of the load cell. Also proper inspection, maintenance and cleaning of the load cell can help overcome some operational issues that might lead to quick re-calibration.


This section provides a comprehensive list of the popular industrial load cell manufacturers and suppliers. If you are looking forward to obtaining standard industrial load cells for your weighing system design, here are the popular load cell original equipment manufacturers (OEMS):

  • Amcells
  • AnyLoad
  • Dale
  • LW Measurements
  • Omega
  • Tacuna Systems


The cost of load cells varies with the type of load cell and it depends on several factors such as its rated capacity, its mode of operation, the material of construction, the requirements of the weighing system etc. The price ranges from about $0.2 for mini load cells to thousands of dollars for load cells with higher rated capacities. Browse our range for a full range of:


In the near future, load cells will find more applications in process automation in various industries.

Load cells will also find more applications in microsystems, hence resulting into something called Miniaturized Load Cells (MEMS). These load cells will be produced as Micro Electro Mechanical Systems (MEMS), which are the latest emerging technologies.

MEMS are micro-sized silicon structures etched in the form of beams, diaphragms or plates that can function as sensors within a load cell. MEMS are fabricated using the bulk and surface micromachining. MEMS can then be mass produced, because thousands of sensor elements can be fabricated on single wafer with integrated supporting circuits. Although millions of sensors can be mass produced at a very low price (as low as a few dollars), their applications are still limited compared with foil strain gauges.

The advantages of these load cells will be higher precision, they will be portable and light weight, enough to be embedded inside materials and even the human body. They can help improve modern medicine and be useful in automatically controlling surgical robot, miniaturized load cell can be incorporated into strength-training equipment to prevent lifting strain. Also the use of multiple miniaturized load cells in robotic artificial limbs to create toes and fingers that can feel pressure and send that data to the brain so the wearer can respond.

Other Sources

  • K. S. K. Singh, "Digital Fuel Indicator in Two Wheelers," IJSRD - International Journal for Scientific Research & Development, vol. 2, no. 12, p. 4, 2015.
  • Guide to the measurement of force, published 1998, by the institute of measurement and control, ISBN 0 904457 28 1
  • Load cell troubleshooting, Technical note VPGT-08, 2015.
  • Digital Load Cells: A Comparative Review of Performance and Application, published 2003 by the Institute Of Measurement and Control, WP0803.
  • A guide to the specification and procurement of industrial process weighing systems, published 2000 by the Institute of Measurement and Control publication, ISDN 0 904457 32 X
  • British Standard BS EN 30012-1: 1994 Metrological confirmation systems for measuring equipment.
  • W. Boyes, Instrumentation Reference Book, Butterworth-Heinemann, 2009.